Synthetic Grass Installation Process

San Diego Artificial Grass Installation Process Each IID installation goes through a 72-Point-Inspection by your dedicated Project Supervisor to insure that every install meets all synthetic turf industry guidelines and our high standards of excellence. 

1. SYNTHETIC LAWN DESIGN AND PLANNING

One of our Professional Design Consultants will assist you with your design and plan in an effort to come up with a clear picture as to your overall vision and goals for this project. The design and diagram will determine the scope of the project. During this process we will also be looking to create as few seams as possible, which will provide for a much more real looking lawn upon completion.

At this point we will be able to provide you with an accurate estimate in regards to your investment. We can continue to alter the scope until we meet your project needs. Once the design is finalized we will use the diagram to figure out the appropriate quantities of material to order.

2. PRE-DEMOLITION

Before the demolition can commence, all utilities (electrical, gas, water, etc.) including all sprinklers must be properly located to eliminate unnecessary problems. Depending on the customer’s preference, the sprinkler system can be capped for use at a later point in time, or we can completely remove it altogether. Any additions or changes to the existing utilities must be accounted for at this time.

3. DEMOLITION

A bob-cat (where applicable) will be used to demolish your existing soft-scape and/or hard-scape surface. In areas where the bob-cat cannot access, or if a bob-cat is not necessary, other demolition tools be used to remove the hard-scape and/or soft-scape. Saw-cutting may be necessary along areas where the foundation is protruding into the usable space in the front, back or side-yard areas.

4. EXCAVATION

We will excavate 2 1/2 to 4 1/2 inches from final grade.

5. GRADING & DRAINAGE

At this point if drains need to be installed, this is the time to do so as well as account for proper water-flow away from your house.

6. INSTALL BORDER (BENDER BOARD OR MOW-STRIP) (OPTIONAL)

For aesthetics and structural integrity of the perimeter, we will install bender board or a paver mow-strip around the outside of your project, where-ever we are abutting up against soft-scape surfaces.

7. SUB-BASE COMPACTING

We will use a plate compactor to compact the sub-base. This is crucial as we do not want to have any air gaps in our system. If you skip this step, it will lead to undulations or depressions later on.

8. WEED KILLER

Spray the entire area rather generously with weed killer to reduce the chances of weeds appearing in the future.

9. BASE PREPARATION & COMPACTION

We will prepare 2-3 inches of Class II Road Base which will be dispersed throughout the entire footprint of your turf project(this is for a Southern California installation as other regions will require different specs). Once the base has been set, we will hose the base down, and compact it until we reach a compaction level of 95%. At this point if the bob-cat drives over the prepared base, you will not see any tires mark, as it is literally hard as a rock, which is exactly what you want.

10. WEED BARRIER FABRIC 

After the base preparation, we recommend that a weed barrier fabric is installed which will reduce the chances of weeds making their way to the surface of the final installation.

    • {Please Note} In terms of weeds, there is zero guarantee about this. We can do everything in our power to destroy them in terms of what is currently there, however, destroying ALL the root systems is nearly impossible. Weeds along the edges of your turf is where you will see them most often. It is very hard to secure the edges 100%, although we do our very best. Synthetic Turf is not synonymous with no maintenance. It means less maintenance than real grass, however, by no means can you get new turf installed and forget about it completely. If you do, it will eventually look shabby. Everything needs maintenance, no matter what a salesman may tell you about their grass…..they all do no matter what.

11. TURF PREPARATION (MEASURE, CUT & ROLL)

Make sure to roll the turf completely out and allow it to sit in the sun during the initial preparation process. Since the turf has been rolled up like carpet, we will want to make sure to eliminate any wrinkles and bunching. If you skip this step, you may see air-pockets in your turf later down the line as the artificial grass has a chance to completely settle.

With proper planning, proceed to position the turf for installation. The goal is to have as few seams as possible and with proper planning this can be achieved every time. Once the fake grass is positioned properly, remove the excess turf that will not be needed, which will make it much easier to work with.

12. SEAMING & TRIMMING

Once the artificial turf has been perfectly laid out and all the excess material has been trimmed, we are now ready to seam the pieces together. It is important to make sure that all the rolls of grass are laid in the same direction, so that the blades all point the same way.

There are several seaming techniques, and the actual technique used on a particular job can vary from job to job depending on the circumstance. The various techniques include utilizing seaming tape in conjunction with adhesives(glue) to sewing to the most popular residential application being tacks and nails.

Once the seams have been completed, the final trimming can take place along all the seams and edges of the grass.

13. BORDER PREPARATION

To properly secure the border it is a good idea to nail down the perimeter with nails. Use 40-60d nails which are 4-6inches in length and use them every 1-2 feet around the perimeter of your project.

14. INFILL PREPARATION

To get the turf ready for the infill installation, you will want to use a power broom and sweep the turf in the opposite direction that the blades are pointing. This will prop the blades upright and allow for the infill to properly penetrate the grass to the base of the turf.

15. INFILL INSTALLATION

Use a standard seed drop spreader to install the infill. The infill is used to help weigh down the turf, assist with blade recovery, soften the feel under your feet, and depending on the actual infill you use, there may be other benefits (i.e. antimicrobial, prevents degradation, reduced heat consumption/overheating). You will need to determine the amount of infill to use in advance because you will want to leave 5/8″ (+/- 1/8″) of the blade of grass exposed. The amount of infill to install will depend on the specific synthetic lawn you choose. The metric will be pounds per sqft, in terms of how many pounds of infill you will need per sqft of artificial grass.

16. FINAL TRIMMING & CLEAN-UP

Walk the project to see if there are any blades of grass that are out of place. If everything looks perfect, then hose down your new lawn which will complete the infill install and now your artificial turf installation is complete and ready for use.

17. MELTING TURF WARNING!!!

 

Instantly Increase Your Curb Appeal & Property Value
Call 858-925-3000

Pin It on Pinterest

Share This